prw2101a0600p_01
4 / 105
5.4.13.
Prog CS........................................................................................................... 64
5.5.
P
ROGRAMMING
D
EVICES
.......................................................................... 65
5.6.
R
EMOTE
P
ROGRAMMING
.......................................................................... 66
5.6.1.
Editing the linearisation table .......................................................................... 68
5.7.
R
ELAY
C
ONFIGURATION
........................................................................... 69
5.7.1.
Relay Selection ............................................................................................... 69
5.7.2.
Properties of the selected relay....................................................................... 70
5.7.3.
Relay programming......................................................................................... 71
5.7.3.1
Source selection ................................................................................. 71
5.7.3.2
Function.............................................................................................. 72
5.7.3.3
Configuring parameters ...................................................................... 80
5.7.3.4
Invert................................................................................................... 81
5.7.3.5
Deleting TOT ...................................................................................... 81
5.7.3.6
Refreshing TOT .................................................................................. 82
5.7.3.7
Testing................................................................................................ 82
5.8.
O
PERATION AND
P
ARAMETERS OF
C
URRENT
O
UTPUTS
.............................. 84
5.8.1.
Selection of Current outputs............................................................................ 84
5.8.2.
Properties of the selected Current Output....................................................... 85
5.8.3.
Current Output programming .......................................................................... 85
5.8.3.1
Source selection ................................................................................. 85
5.8.3.2
Function.............................................................................................. 86
5.8.3.3
Parameter configuration ..................................................................... 87
5.8.3.4
Testing................................................................................................ 87
5.9.
T
HE
B
OOT
P
ROCESS
............................................................................... 88
5.10.
M
EASUREMENT
M
ODES
........................................................................... 90
5.11.
S
AVING
,
L
OADING THE CONFIGURATION OF THE
M
ULTI
CONT..................... 91
6.
ERROR CODES............................................................................................. 92
7.
HARDWARE PROTECTION OF THE SETTINGS ........................................ 94
8.
FUSE REPLACEMENT ................................................................................. 95
9.
SERVICING.................................................................................................... 96
9.1.
B
OX
M
ESSAGES
:..................................................................................... 96
9.2.
O
THER
M
ESSAGES
:................................................................................. 97
9.3.
T
ROUBLESHOOTING
................................................................................. 98
9.3.1.
It is impossible to enter the „Main menu”/”Relays” or „Main menu”/„Current
outputs” menu: ................................................................................................ 98
9.3.2.
It is impossible to enter the „Main menu”/”Devices” menu: ............................. 98
9.3.3.
A „Please wait” message appears upon selecting „DEV detect”.................... 98
9.3.4.
The result of „DEV detect” is the „No device” message .................................. 98
9.3.5.
The unit does not start up when switched on ..................................................98
9.3.6.
The „Response” error entry is too frequent......................................................98
9.4.
A
DDITIONAL
I
NFORMATION
........................................................................99
9.4.1.
Problems that may occur during remote programming:...................................99
9.4.2.
MultiCONT transmits the parameters without examining them, and the testing is
done by the device...........................................................................................99
9.4.3.
Use of Second HART Master ( Hand-Held or HART modem + Eview
configuration software) ....................................................................................99
9.4.4.
Upon exiting remote programming, the unit tests to see if the transmitter really
exited the remote programming mode.............................................................99
9.4.5.
When a transmitter does not respond, then „Response” error is entered into the
table, but upon termination of the error (the device responds), this entry is
automatically cleared from the table (and does not need to be acknowledged)99
9.4.6.
Upon exiting the menu, MultiCONT immediately saves the modifications.......99
9.4.7.
The error list is cleared when the device is put off...........................................99
Appendix 1. ManufacturerID codes of HART-capable devices
100
Appendix 2. The menu system of the MultiCONT P-200
101-102
Appendix 3. Relay programming
103
Appendix 4. Current output programming
104
Appendix 5. Measurement mode
105
Summary of Contents for MultiCONT
Page 2: ...prw2101a0600p_01 2 105 ...
