Nikon ECLIPSE 80i Instructions Manual Download Page 67

Page: 67 / 72

Chapter 6 Troubleshooting

6.2 Electrical

Problem

Possible causes

Remedy

Revolving nosepiece not installed
correctly, or not rotated to the click
stop position

Install correctly and rotate to the click
stop position.

Specimen projecting from the stage
surface

Securely attach the specimen to the
stage specimen holder.

Image flows

Condenser tilted

Install correctly and rotate to the click
stop position.

NCB11 filter not being used

Use the NCB11 filter.

Yellow-tinged

Lamp voltage too low

View field too bright

Lamp voltage too high
Lamp voltage too low

Press the Preset switch and adjust the
brightness to match the ND filter
combination.

Condenser aperture diaphragm
stopped down too far

Open the aperture diaphragm to the
proper setting.

Condenser maladjusted

Adjust the condenser so that the field
diaphragm image is shown in the center
of the viewing field.

View field too dark

Image light spread over too great
an area

Adjust the light path switching lever to
provide the target location with 100%
light.

Specimen upside down

Attach the specimen to the stage with the
cover glass face up.

Unspecified cover glass thickness

Attach a cover glass of the specified
thickness (0.17 mm).

Focus impossible on a
high-magnification
objective

Diopter not adjusted

Adjust the diopter.

Too great a difference
in focus after objective
switching.

Diopter not adjusted

Adjust the diopter.

Specimen not moving
smoothly

Specimen holder insufficiently
attached to stage

Attach the specimen holder securely to
the stage.

Interpupillary distance incorrect

Make adjustment

Images on the left and
right eyepiece not
coincident

Diopter not adjusted

Adjust the diopter.

6.2

Electrical

Problem

Possible causes

Remedy

No power despite power
switch turned on

Power cord not connected or
connected improperly

Connect properly.

Lamp burned out

Replace with specified lamp.

Lamp does not light

Impossible to install the lamp

Replace with specified lamp.

Lamp burns out quickly

Lamp used is
unspecified/incompatible

Replace with specified lamp.

Microscope brightness
control knob not
functional

Preset switch off

If off, switch it on.

Summary of Contents for ECLIPSE 80i









































































Search results

Summary of Contents for ECLIPSE 80i

Reviews:

Related manuals for ECLIPSE 80i

Brands by name

Popular brands

Nikon ECLIPSE 80i, Instructions Manual

Search results

Summary of Contents for ECLIPSE 80i

Reviews:

Related manuals for ECLIPSE 80i

Brands by name

Popular brands