Nikon ECLIPSE 80i Instructions Manual Download Page 61 | Manualshive

Page: 61 / 72

background image

Chapter 4 Assembly

59

4

9

Installing a Revolving Nosepiece

(1)

Lift the revolving nosepiece from a position

just forward of the point directly below the
fitting part and slide toward the back to
attach. (Continue sliding the revolving
nosepiece until its front position is aligned
with that of the fitting part.)

(2)

Secure with the screw.

(3)

When using the intelligent revolving

nosepiece, connect the connector attached to
the revolving nosepiece to the upper port
found inside the C-BOX.

10

Installing Objectives

Screw objectives into the revolving nosepiece. When installing the objective in this way, make
sure that the magnification of the objective increases when the revolving nosepiece is turned
clockwise (clockwise when viewed from above the eyepiece).

Fixing the revolving nosepiece

Connect the connector

here when using the

intelligent revolving

nosepiece.

«
...
59
60
61
62
63
...
»

Summary of Contents for ECLIPSE 80i









































































Reviews:

No comments

Related manuals for ECLIPSE 80i

Brand: Zeiss Pages: 17

Brand: LABSTAC Pages: 17

Brand: LABSTAC Pages: 20

Brand: Hitachi Pages: 6

Brand: Zuzi Pages: 20

Brand: Thermo Scientific Pages: 12

Brand: Motic Pages: 3

Brand: Motic Pages: 3

Brand: Motic Pages: 7

Brand: Motic Pages: 2

SWIFTLINE SM100 Series

Brand: Motic Pages: 13

Moticam S Series

Brand: Motic Pages: 6

Brand: Motic Pages: 10

Brand: Motic Pages: 11

Brand: Motic Pages: 9

Brand: Motic Pages: 8

F-11 LED Series

Brand: Motic Pages: 10

Brand: Motic Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands