manualshive.com logo in svg

Nikon DTM-502 Series, Instruction Manual

Share
Download
Nikon DTM-502 Series Instruction Manual Download Page 58

 

3 

ANG

3-4. Applications 

ANG

1)  HA Reset and Angle Operations 

Press the [ANG] key to display the angle menu 
screen.  Select the desired item by pressing the 
numeric key or moving the highlight with the arrow 
keys and pressing the [ENT] key. 
 
 
 
 

1. 0-Set 
Setting the Horizontal Angle to 0 

Press the [1] key to reset the horizontal angle to 0.  
The display returns to the basic measurement screen 
(BMS) after resetting the horizontal angle. 
 
 

2. Input 
Inputting the Horizontal Angle 

Press the [2] key, and the numeric input screen is 
displayed.  Input the horizontal angle by the 
numeric keys and press the [ENT] key. 
 
 

 
 

 
 
 

•

 

To enter 123º45’50”, key input should be 123.4550. 

• 

The displayed value is rounded to the minimum increment of angle. 

 

3-32 

Summary of Contents for DTM-502 Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands