Nikon DTM-502 Series Instruction Manual Download Page 130

Page: 130 / 201

4. Data
Viewing and Editing Records

Press the [4] key on the MENU screen to display the
Data menu.

MENU:

4. Data

4-1. View Records

•

“Data View” feature is available at all times even from observation or inputting PT

screens.

4-1-1. View data from RAW data

Press the [1] key on the Data menu screen to show
the RAW data in List form.

When you first view the RAW data, you will see the
last four RAW records in the current Job. You can
use the Up/Down arrow keys to scroll through the
records.

[ENT]

Press [ENT] to see the records detailed information.
Press [ESC] to return to the list screen.

SS/CP/F1/F2 records

RAW record of these record types consist of “PT”, “HT”, “CD”, and
“HA/VA/SD”.

SS:

Sideshots (Topo shots). All shots from the BMS.

CP:

Shots taken in the ANG/Rept and the BMS (See p.3-33, 3-68).

F1/F2: Face1/Face2 records.

3-104

Summary of Contents for DTM-502 Series










































































































































































































Search results

Summary of Contents for DTM-502 Series

Reviews:

Brands by name

Popular brands

Nikon DTM-502 Series, Instruction Manual

Search results

Summary of Contents for DTM-502 Series

Reviews:

Brands by name

Popular brands