manualshive.com logo in svg

Nikon DTM-502 Series, Instruction Manual

Share
Download
Nikon DTM-502 Series Instruction Manual Download Page 168

 

4 

CHECKING

 AND

 ADJU

S

TMEN

T

Only when the setting “HA corr.” is set to OFF 
while you complete updating the trunnion axis 
parameter, a question screen to change the setting 
will be shown. 
Press the [Yes] softkey to change the setting 
([ENT] doesn’t work here). 
 
 
================== 

Trunnion axis compensation

 =================== 

 
The trunnion axis error, which is reported when the vertical axis and the trunnion 
axis (horizontal axis) are not perpendicular to each other, and the sighting axis 
error, which is from the sighting and the trunnion axes, can be compensated by the 
Tr-axis and ACH parameters on this instrument. 
 
 

<Plane view>

<Front view> 

 

ACH

 

Tr-axis

 
 
 
 
 
 
 
 
These parameters are applied to horizontal angle readings. 
Since the amount of the compensation is changed in proportion to its vertical angle, 
while the compensation is set to ON (HA corr.=ON) you can see a slight movement 
in horizontal angle even if you clamp the tangent screw. 
 
=========================================================== 
 

4-7 

Summary of Contents for DTM-502 Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands