manualshive.com logo in svg

Nikon DTM-502 Series, Instruction Manual

Share
Download
Nikon DTM-502 Series Instruction Manual Download Page 132

 

SO records 

SO: Stakeout shots.  Shots recorded in Stakeout functions. 

 
Pressing the [DSP] key switches the display in the following order when the “Store 
DB” setting sets to “RAW+XYZ”.. 
 

3 

MENU: 

4. Data

 
 
 
 
 
 
 
 
 
 
 

1st screen 

HA: 
VA: 
SD: 
PT: 
HT: 

2nd screen 

X:
Y: 
Z: 

PT:
CD

:

3

ｒ

d screen 

dX:
dY: 
dZ: 
PT:
CD:

•

  dX/dY/dZ is difference in coordinates to its planned (designed) position.  It will be

downloaded as a comment record in Nikon RAW format. 

 

CO records 

A comment added to the job from the system. 
For example, when you change the Stn-Z by the Remote Benchmark function, or 
the horizontal angle is reset by the BSCheck function, the system records what 
you have done in the field. 

 
A sample comment record from the Remote 
Benchmark function is shown right. 

 

 
 
 
Temperature, Pressure and Prism Constant record 
(SY record) is also stored when you complete a 
station setup. 
 
 

3-106 

Summary of Contents for DTM-502 Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands