manualshive.com logo in svg

Nikon DTM-502 Series, Instruction Manual

Share
Download
Nikon DTM-502 Series Instruction Manual Download Page 104

 

When a measurement is taken to the forth point, the corner point can be 
calculated as the intersection of two walls (P1-P2 and P3-P4).  The default 
elevation is given by P4. 
 
 
 
 

3 

O/S: 

6. Corn

e

r

 
 
 
Input PT (and CD).  Height of target is defaulted to 
the one used in the last measurement. 
Press [ENT] to record the corner point. 
 
 
 

= Sample records in [O/S] 

→

 [6: Corner] = 

SS, 58, 0.0000, 48.3304, 169.19165, 82.02470, 10:52:37, FLOOR2 

CO, PT1, 1.0080, 48.3020,169.19165, 83.58565 

CO, PT2, 1.0080, 48.3155,128.54250, 85.42440 

CO, PT3, 1.6528, 74.0362,57.07330, 80.11485 

 
 

•

  The calculated corner point is stored as a SS record. 

•

  Next three or four comment lines are measured points. 

  CO, Point name (fixed to PT1, PT2  etc.), HT, SD, HA, VA 

3-78 

Summary of Contents for DTM-502 Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands