manualshive.com logo in svg

Nikon DTM-502 Series, Instruction Manual

Share
Download
Nikon DTM-502 Series Instruction Manual Download Page 35

 

3

Input P

oint Name/Numbe

r

5. When the [MSR] Softkey is Pressed 

You can also input a point by on-the-spot 
measurement.  Press the [MSR] softkey. 
 
 
 
 

[MSR] 

 
An observation screen is shown. 
Press [MSR1] or [MSR2] to start a measurement.  
When you need to change the Height of Target, 
press the [HT] softkey. 
 
 
After a measurement, press [ENT] to proceed to the 
point recording screen. 
Input PT/CD and press [ENT]. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

•

  The default value is inverted when the cursor is 

moved. (‘All-Replace’ mode) 
 
 
 
 

•

  Press the Right arrow key and the input mode 

changes to ‘Overwrite’ mode at the first character.  
Press the Left arrow key and the cursor moves to 
the end of the string. 

3-9 

Summary of Contents for DTM-502 Series










































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands