Nikon DTM-502 Series Instruction Manual Download Page 201

Page: 201 / 201

LED safety

The DTM-552/532/522 is a class 1 LED instrument.
Class 1 LED instruments do not require any special precautions, signage or training for LED
safety.

Specifications for LED emission

- Wave length:

850nm

- Drive method:

- Output power:

< 200

- Repetition rate: 15KHz

Safety class

- E.U.:

EN60825-1/Am.2:2001 (IEC60825-1/Am.2:2001), class 1

- Japan: JIS C6802-1997, class 1

•

It is prohibited to alter this manual in part or whole without expressed permission.

•

The contents of this manual are subject to changed without any notice.

•

Although every effort has been made to ensure the accuracy of this manual, if you

note any points that are unclear or incorrect, contact your nearest Nikon GEOTECS
representative.

Summary of Contents for DTM-502 Series










































































































































































































Search results

Summary of Contents for DTM-502 Series

Reviews:

Brands by name

Popular brands

Nikon DTM-502 Series, Instruction Manual

Search results

Summary of Contents for DTM-502 Series

Reviews:

Brands by name

Popular brands