410-00352
EN
PM410-00352R20383
Before installing the device, carefully read this operating manual.
1. DESCRIPTION
The 410-00352 DIN rail receiver is used for control of tubular motors. Different modes are used for controlling
roller shutters and blinds.
1.1. Controlling roller shutters and blinds
1.1.1. ROLLER SHUTTER OPERATING MODES (R)
Roller shutter operating modes (R) generally carry out positioning commands immediately in self-maintained
mode. Pressing the transmitter button briefly is all that is needed to move to a position (for example to open or
close the roller shutter).
1.1.2. BLIND OPERATING MODES (J)
In blind operating modes (J), to adjust the slats, each positioning command is initially interpreted as a push
button command. That means, that the blind will only move for as long as the transmitter button is held down.
If the transmitter button is pressed for >1.6 seconds, the control system goes into self-maintained mode and
the blind moves independently to a position or an end point.
1.2. Lock mode
The lock mode allows the CLOSE direction of one or several outputs to be locked, therefore preventing accidental
lockout. To do this, a separate transmitter must be programmed with the corresponding operating mode. Only
transmitters with 2-button-operation (ON/OFF) can be used. If the lock mode is activated with the transmitter, the
output only travels in the OPEN direction. If an attempt is made to travel in the CLOSE direction, the command
is rejected and the LED for the corresponding channel flashes for 2 seconds.
1.3. Positioning
Roller shutters and blinds can both be programmed with up to three positions. These can then be specifically
approached with the relevant programmed transmitter. Positions are always approached from above to enable
maximum precision. To be able to move positions, a runtime measurement for the connected roller shutter (or
blind) is needed first.
1.4. Adjustable runtime
The runtimes for each output in OPEN and CLOSE directions are individually measured and saved. The factory
default setting is a runtime of 90 seconds. The maximum runtime that can be set is approximately 2 hours.
1.5. Adjustable reversing time
For blind operating mode (J), each output can be programmed with a separate reversing time. If the reversing
time has been programmed, after each STOP signal received during closing (CLOSE), the blind slats move in the
OPEN direction for the set amount of time. Also, each time the position is changed, the blind reverses as soon
as the position has been reached. So, the desired slat angle can be attained automatically after every position
change. In default factory settings the reversing mode is deactivated.
2. INSTALLATION
The device is intended for installation on a standard DIN rail (35 x 7.5 mm).
1. Switch off the power supply.
2. Mount the 410-00352 onto the rail.
3. Connect the cables for the power supply and for the devices in accordance with the connection diagram.
230V~
L
N
PE
4. Switch on the supply voltage.
5. Program the receiver according to the operating manual.
In unfavourable environmental conditions, the external antenna 410-00359 can be used to improve wireless
reception (to be bought separately).
3. OPERATION AND USE
The device shall only be operated at AC voltages of 230 V / 50 Hz. Operate the devices only with loads that do
not exceed the specified power limits (see § Specifications). This device is only intended for indoor use in dry
and dust-free rooms. This module may only be used as a wireless receiver for switching electrical devices. To
be operated with wireless transmitters following the Easywave protocol.
3.1. Display
Display
Operating status
Programming mode
LED
GREEN
POWER
Power
Supply voltage is on, LED is lit
LED
RED
3TB
3-button operation
LED 3TB flashes when a wire-
less signal is detected
Displays the selected operation
2TB
2-button operation
Signals the programming or
delete mode
1
LED output 1 flashes Output 1 activated
Displays the output selected for
programming
2
LED output 2 flashes Output 2 activated
Digital display
O...L
Upon receiving a programmed
transmission code, the cor-
responding operating mode is
displayed for 2 s.
Displays the selected operating
mode
Operating
Operating status
Programming mode
Programming button
Start programming mode and
select an operation
Mode button
Select an operating mode
Channel 1 button
Operate output 1 manually
(OPEN/CLOSE alternately)
Select output 1
Channel 2 button
Operate output 2 manually
(OPEN/CLOSE alternately)
Select output 2
Note: If you change the programming mode, all outputs are switched off, the HOLD function is deactivated, and
no control is possible during programming. If you return to operating mode, the outputs remain switched off.
3.2. Operation
3.2.1. 3-BUTTON OPERATION
In a 3-button operation (3TB), transmitter button A has the function OPEN (roller shutters/blinds are opened),
transmitter button B has the function CLOSE (roller shutters/blinds are closed) and buttons C and D (if present)
have the function STOP (movement is stopped).
For this operation, a transmitter with at least three connected buttons is necessary. Only one transmission button
must be programmed in the receiver. The code for additional buttons is assigned automatically.
3.2.2. 2-BUTTON OPERATION
In a 2-button operation (2TB), transmitter button A has the function OPEN (roller shutters/blinds are opened),
transmitter button B has the function CLOSE (roller shutters/blinds are closed). The movement is stopped by
pressing the button for the opposite direction.
For this operation, a transmitter with two connected buttons is sufficient. Only one transmission button must be
programmed in the receiver. The code for additional buttons is assigned automatically.
A
B
C
D
05-317
D
C
A
B
A
B
A
B
A
B
A
B
C
05-312
A
B
C
K
05-318
410-00002
A
B
C
D
