Nidec SHIMPO DT-5TFR, Instruction Manual

Page: 9 / 20

9
䖂
About Hysteresis
The output values for the same input differ
when input is increased and decreased. This
phenomenon or the difference between these
two amounts is called hysteresis.
㻻㼡㼠㼜㼡㼠
㻻㻲㻲
㻜
㻰㼕㼟㼜㼘㼍㼥㻌㼢㼍㼘㼡㼑
㻥㻥㻜 㻝㻜㻜㻜
㻴㼕㼓㼔㻌㼟㼑㼠㻌㼜㼛㼕㼚㼠㻌㻝㻌㼛㼡㼠㼜㼡㼠
㻻㻺
㻻㼡㼠㼜㼡㼠
㻻㻲㻲
㻜
㻻㻺
㻻㻲㻲㻌㼐㼕㼟㼜㼘㼍㼥
㼢㼍㼘㼡㼑
㻻㻺㻌㼐㼕㼟㼜㼘㼍㼥
㼢㼍㼘㼡㼑
㻰㼕㼟㼜㼘㼍㼥
㼢㼍㼘㼡㼑
㻴㼥㼟㼠㼑㼞㼑㼟㼕㼟
[Example]
For high set point 1 value (also applicable
to low set point 1, high set point 2, and low
set point 2 values), assuming the high set
point 1 value is 1000 and hysteresis is 10:
When the displayed value is 1000, output is
turned ON, and when it is 990, OFF.
䖂
About Display
Use Function 5 (Sub-display's display pattern selection) to select the desired display pattern from the following three:
䞉
Display pattern (1)
(Set value: 0)
㻹㼍㼕㼚㻌㼐㼕㼟㼜㼘㼍㼥
㻹㼑㼍㼟㼡㼞㼕㼚㼓㻌㼢㼍㼘㼡㼑
㻴㼕㼓㼔㻌㼟㼑㼠㻌㼜㼛㼕㼚㼠㻌
㻝㻌㼢㼍㼘㼡㼑
㻸㼛㼣㻌㼟㼑㼠㻌㼜㼛㼕㼚㼠㻌
㻝㻌㼢㼍㼘㼡㼑㻌
㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻭 㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻮
䞉
Display pattern (2)
(Set value: 1)
㻹㼍㼕㼚㻌㼐㼕㼟㼜㼘㼍㼥
㻹㼑㼍㼟㼡㼞㼕㼚㼓㻌㼢㼍㼘㼡㼑
㻮㼘㼍㼚㼗
㻮㼘㼍㼚㼗
㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻭 㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻮
䞉
Display pattern (3)
(Set value: 2)
㻹㼍㼕㼚㻌㼐㼕㼟㼜㼘㼍㼥
㻹㼑㼍㼟㼡㼞㼕㼚㼓㻌㼢㼍㼘㼡㼑
㼞㼜㼙 㻮㼘㼍㼚㼗
㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻭 㻿㼡㼎㻙㼐㼕㼟㼜㼘㼍㼥㻌㻮
* When the high and low set
point 1 values have not been
designated, "0" is displayed.
䖂
Time of Moving Average
The frequency of moving average can be selected via function 7.
Measurement is performed using the cycle designated via pa-
rameter 4 (display cycle) and averaging the data via function
7's set value (frequency).
㻲㻣 㻜 㻝 㻞
㼀㼕㼙㼑㼟㻌㼛㼒㻌㼙㼛㼢㼕㼚㼓㻌㼍㼢㼑㼞㼍㼓㼑 㻺㼛㼚㼑 㼀㼔㼞㼑㼑㻌㼠㼕㼙㼑㼟 㼀㼑㼚㻌㼠㼕㼙㼑㼟