Nexxt NOVA300 AML02304U1 User Manual Download

Page: 74 / 75

146

147

Nova300 - ADSL wireless modem router

CE Mark Warning

This is a Class B product in a domestic environment, this product may cause radio interference, in which

case the user may be required to take adequate measures. This device complies with EU 1999/5/EC.

NOTE:

(1)The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to

use a shielded RJ45 cable

Appendix 5 Regulatory Compliance Information

India

morocco

Malaysia

Indonesia Speedy Telkomnet

MTNL

RELIANCE COMMUNICATION

TATA INDICOM

CONNECT

IAM

Streamyx

1483 Bridged IP LLC

PPPOE LLC

PPPOE

PPPOE LLC

PPPoE LLC

Country

ISP

VPI

VCI

Encapsulation

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC caution:

Any changes or modifications not expressly approved by the party responsible for complian-

ce could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmit-

ter.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifica-

tions to this equipment.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

NOTE:

(1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to

use a shielded RJ45 cable.

Summary of Contents for NOVA300 AML02304U1












































































Search results

Summary of Contents for NOVA300 AML02304U1

Reviews:

Related manuals for NOVA300 AML02304U1

Brands by name

Popular brands

Nexxt NOVA300 AML02304U1, User Manual

Search results

Summary of Contents for NOVA300 AML02304U1

Reviews:

Related manuals for NOVA300 AML02304U1

Brands by name

Popular brands