Newland NLS-BS80 User Manual Download Page 39

Page: 39 / 264

Barcode Separator

A separator with length up to 10 characters (default: none) can be inserted between barcodes. This

feature is only available when the following two conditions are met: Bluetooth or USB batch transmission

is selected and Packet mode is off. Scan the appropriate barcode below to enable or disable this feature.

When barcode separator is enabled, the preset separator will be inserted between barcodes and it will be

sent three times after batch transmission is completed.

Enable Barcode Separator

Disable Barcode Separator (default)

To set the barcode separator, scan the

Set Barcode Separator

barcode, the numeric barcodes that

represent the hexadecimal value of each character contained in your desired separator and the

Save

barcode.

Set Barcode Separator

Query Barcode Separator

Example: Set the barcode separator

to “*” (Hex: 0x2A)

Scan the

Set Barcode Separator

barcode.

2. Scan the numeric barcodes

“2” and “A” from the “Digit Barcodes” section in Appendix.

3. Scan the

Save

barcode from the Save/Cancel Barcodes

” section in Appendix.

Summary of Contents for NLS-BS80









































































































































































































































































Search results

Summary of Contents for NLS-BS80

Reviews:

Related manuals for NLS-BS80

Brands by name

Popular brands

Newland NLS-BS80, User Manual

Search results

Summary of Contents for NLS-BS80

Reviews:

Related manuals for NLS-BS80

Brands by name

Popular brands