background image

NRP1004 Series IP Phone                                                                        User Manual 

New Rock Technologies, Inc.                                                                                                                                                          5-19 

Name Description 

 
Proxy Server 
Address 

Specifies the IP address of a proxy server. (Usually, the SIP service provider provides 
a server with configurations of the proxy server and registration server being identical. 
If configurations (such as the IP address) of the proxy server and registration server are 
different, you need to make modifications as needed. 

Proxy Server Port 

Specifies the signaling port of the SIP proxy server.   

Proxy User 

Specifies the account of the SIP proxy server. 

Proxy Password 

Specifies the password of the SIP proxy server. 

Backup Server 
Address 

Specifies the IP address of the backup server. I If the IP address of the primary server 
is unavailable, the phone will use the backup server address. 

Backup Server 
Port 

Specifies the port of the backup server. 

Server Name 

 

Codecs Settings

 

Disable 
Codecs/Enable 
Codecs 

Adds or deletes codecs, and changes the codecs priority through the navigation keys. 

Advanced SIP Settings 

Forward Type 

Specifies the call forward mode. By default, call forward is disabled. 

Disabled

: disables call forward. 

Busy

: forwards the call to a specified number if the phone is busy. 

No answer

: forwards the call not answered within the specified time to a specified 

number. 

Always

: forwards all incoming calls to a specified number under any conditions. 

The phone will prompt you of the incoming before carrying out the forwarding 
operation. 

Forward Number    Specifies the number the incoming call will be forwarded to. 

No Ans. Fwd 
Wait Time 

Forwards the incoming call to a specified number at a certain delay in the scenario 
where the forward type is set to No answer and the, incoming call is not answered in 
time. 

Transfer Timeout 

For the phone supports the transfer of certain special features server, set interval time 
between sending “bye” and hanging up after the phone transfers a call. 

Enable Hotline   

Enables the hot line function. 

Hotline Number 

Sets a hot line number for the phone to dial automatically after the handset is picked up 
for a certain period of time. 

Warm Line Wait 
Time 

Sets the hot line delay time. 

BLF Server 

Sets this parameter if your server does not support subscription package to separates 
the registration server from the subscription server. Because ordinary BLF application 
will send subscription package to the registration server 

SIP Encryption 

Enables or disables SIP encryption. 

SIP Encryption 
Key 

Sets the key for SIP encryption. 

RTP Encryption 

Enables or disables RTP encryption. 

RTP Encryption 
Key 

Sets the key for RTP encryption. 

Enable Auto 
Answer 

Enables Auto Answer. 

Summary of Contents for NRP1004 Series






























































































Reviews: