New Holland E37C Original Instructions Manual Download Page 170

Page: 170 / 296

6 - MAINTENANCE

Fuel filter water separator

Drain water and sediment from the fuel filter water separator every

10 h

or every day.

Clean the filter element of the fuel filter water separator every

200 h

Drain water

1. Open the engine hood to access to the fuel filter water

separator and place a container with an appropriate
capacity under the fuel filter water separator

(1)

SMIL16MEX1445AA

2. Rotate clockwise the fuel cock

(2)

located on the fuel

filter water separator

(1)

to close the fuel flow.

3. Loosen the drain plug

(3)

located at the bottom of the

fuel filter water separator.

4. Drain the water collected inside.

5. Tighten the drain plug

(3)

1 – 2 N·m

(

0.7 – 1.5 lb ft

)

6. Open the fuel cock

(2)

7. Prime the fuel system.

8. Check for leaks.

SMIL16MEX0600AB

Priming the fuel system

1. Turn the starter switch to ON position for

10 – 15 s

. The

electric fuel pump prime the fuel system.

NOTE:

never use the starter motor to crank the engine in

order to prime the fuel system. This may cause the starter
motor to overheat and damage the coils, the pinion and/or
the ring gear.

SMIL19MEX0717AA

6-24

Summary of Contents for E37C









































































































































































































































































































Search results

Summary of Contents for E37C

Reviews:

Related manuals for E37C

Brands by name

Popular brands

New Holland E37C, Original Instructions Manual

Search results

Summary of Contents for E37C

Reviews:

Related manuals for E37C

Brands by name

Popular brands