New Holland E37C Original Instructions Manual Download Page 74 | Manualshive

Page: 74 / 296

background image

3 - CONTROLS AND INSTRUMENTS

Safety lock lever

WARNING

Unexpected machine movement!
When you must leave the operator’s seat, al-
ways place the safety lever in the LOCKED po-
sition. If the safety lever is unlocked and the
control lever is moved unexpectedly, a serious
accident could result.
Failure to comply could result in death or se-
rious injury.

W1241A

The safety lever operates on two positions:

A. Locked position: when the safety lever

(1)

is in locked

position

(A)

, all the functions are disabled.

NOTICE:

never use the safety lock lever as a hand-

hold when get in or out the machine.

B. Unlocked position: when the safety lever

(1)

is in un-

locked position

(B)

, the machine is operative.

SMIL16MEX2743AA

1

Engine speed control

The knob

(1)

is used to increase or decrease the rotation

speed of engine (RPM).

See the relevant decal locate on the left hand console.

Rotate the knob clockwise

(A)

to increase engine RPM.

Rotate the knob counterclockwise

(B)

to decrease engine

RPM.

NOTE:

when stop the engine, rotate the engine speed

control in low idle position and turn the starter key OFF.

SMIL16MEX2743AA

1

3-16

«
...
72
73
74
75
76
...
»

Summary of Contents for E37C









































































































































































































































































































Reviews:

No comments

Related manuals for E37C

Brand: jcb Pages: 41

Brand: EVERDIGM Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands