New Holland E37C Original Instructions Manual Download Page 79 | Manualshive

Page: 79 / 296

background image

3 - CONTROLS AND INSTRUMENTS

Starter switch

The starter switch has the following positions:

(1)

OFF: engine shut–down. The electrical circuits are

not activated.

(2)

ON: contact, all the systems of the machine operate.

The buzzer sounds for

1 s

.

NOTICE:

if this alarm does not sound, the electric cir-

cuit is abnormal. Contact your NEW HOLLAND CON-
STRUCTION dealer for inspection and maintenance.

(3)

START: engine ignition.

NOTE:

if the weather temperature is below

10 °C

(

50 °F

),

turn the starter switch to ON position and wait the preheat
pilot lamp turns off. Then start the engine by turning the
starter switch to the START position.

NOTE:

the starter key is also used to lock the cab door,

the side hoods, and the storage compartment.

SMIL19MEX0717AA

5

Washer/wiper switch (cab version only)

The washer/wiper switch

(12)

activates the wiper and the

washer in two steps.

First step: wiper activation.

Second step: washer activation. The washer liquid is
sprayed and the wiper is operative only while the switch is
pressed. If the washer/wiper switch is released, it returns
to first step.

SMIL16MEX0392AA

6

3-21

«
...
77
78
79
80
81
...
»

Summary of Contents for E37C









































































































































































































































































































Reviews:

No comments

Related manuals for E37C

Brand: Takeuchi Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands