New Holland E37C Original Instructions Manual Download Page 154 | Manualshive

Page: 154 / 296

background image

6 - MAINTENANCE

Fuel

For Europe only: use only Ultra-Low Sulfur Diesel (S10) that meets

EN 590

specifications.

For North America only: use only No. 2-D Ultra-Low Sulfur Diesel ( S15) that meets

ASTM D975

specifications.

Using other types of fuel may lead to stalled engine output or deterioration in fuel economy.

NOTICE:

the warranty shall be invalid if any serious defect is caused by usage of any other fuel. Using fuel other than

recommended may cause damage to the fuel injection pump, injector, and other fuel supply system or the engine.
NEW HOLLAND CONSTRUCTION may not be responsible to any of such damages.

If the temperature drops below the fuel cloud point, output deficiency or engine start problems may occur due to wax
crystals.

For North America only: during cold weather, lower than

-7 °C

(

19.4 °F

), it is temporarily acceptable to use a mixture

of No. 1-D (S15) and No. 2-D (S15).

NOTICE:

if operating in severe winter climate, consult the fuel supplier or the NEW HOLLAND CONSTRUCTION

dealer for specific diesel fuel to be used.

The diesel fuel to be used on the machine shall:

• be free from dust particles, even minute ones.

• have the proper viscosity.

• have a high cetane number.

• present great fluidity at low temperatures.

• have low sulfur content.

• have very little residual carbon.

NOTICE:

never use a mix of diesel fuel and old engine oil. The fuel injection system and the exhaust after treatment

system will be severely damaged.

NOTICE:

consult the fuel supplier or the NEW HOLLAND CONSTRUCTION dealer regarding appropriate use of fuel

additives.

NOTICE:

in order to prevent condensation during cold weather, fill the fuel tank to full after completing the day's work.

Fuel storage:

Long storage can lead to the accumulation of impurities and condensation in the fuel. Engine trouble can often be
traced to the presence of water in the fuel. The storage tank must be placed outside and the temperature of the fuel
should be kept as low as possible. Drain off water and impurities regularly.

6-8

«
...
152
153
154
155
156
...
»

Summary of Contents for E37C









































































































































































































































































































Reviews:

No comments

Related manuals for E37C

PC600-8R BACKHOE

Brand: Komatsu Pages: 10

Brand: Kubota Pages: 123

Brand: Komatsu Pages: 51

Galeo PC800LC-8

Brand: Komatsu Pages: 318

Brand: Cub Cadet Pages: 180

Brand: BOXER Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands