New Holland E37C Original Instructions Manual Download Page 48

Page: 48 / 296

2 - SAFETY INFORMATION

(11)

Parking the machine

Location: this sign is located on the left-hand console box.

Quantity: 1

Part number: 91M8-07300

To prevent unauthorized and unintended movement of
the machine, always do the following before you leave
the operator’s compartment:

1. Lower the bucket to the ground completely.

2. Place the safety lock lever in the raised position.

3. Stop the engine.

4. Remove the key.

SMIL16MEX0015AA

(12)

Safety front window

Location: these signs are located on the both side window
of the cab.

Quantity: 2

Part number: 97MH-07351

Be careful that the front window may be promptly closed.
During the machine movements the window could fall in-
juring the operator.

SMIL19MEX0708AA

(13)

Dozer blade operation

Location: this sign is located on the right-hand console
box.

Quantity: 1

Part number: 91M9-07391

This sign describes the blade operations.

SMIL16MEX0010AA

2-26

Summary of Contents for E37C









































































































































































































































































































Search results

Summary of Contents for E37C

Reviews:

Related manuals for E37C

Brands by name

Popular brands

New Holland E37C, Original Instructions Manual

Search results

Summary of Contents for E37C

Reviews:

Related manuals for E37C

Brands by name

Popular brands