NETGEAR Nighthawk X4S R7800 User Manual Download Page 159

Page: 159 / 160

Default Behavior

Feature

Enabled

Wireless communication

Wireless

See router label

SSID name

WPA2-PSK (AES)

Security

Enabled

Broadcast SSID

Auto

Transmission speed

United States in the US; otherwise, varies by region

Country/region

Auto for 2.4GHz, CH 44 for WW SKU and CH 153 for North
America SKU

RF channel

Up to 600 Mbps at 2.4 GHz, 1733 Mbps at 5 GHz

Operating mode

Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network conditions and

environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data

throughput rate.

Technical Specifications

Table 4. R7800 router specifications

Description

Feature

TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond, Dynamic DNS, UPnP, and SMB

Data and routing protocols

•

North America: 100-240V, 50/60 Hz input

•

UK, Australia: 100-240V, 50/60 Hz, input

•

Europe: 100-240V, 50/60 Hz input

•

All regions (output): 12V/3.5A DC output

Power adapter

11.22 x 7.26 x 1.97 in. (285 x 184.5 x 50 mm)

Dimensions

1.65 lb (750 g)

Weight

0° to 40°C (32º to 104ºF)

Operating temperature

90% maximum relative humidity, noncondensing

Operating humidity

Supplemental Information

159

Nighthawk X4S AC2600 Smart WiFi Router

Summary of Contents for Nighthawk X4S R7800

































































































































































Search results

Summary of Contents for Nighthawk X4S R7800

Reviews:

Related manuals for Nighthawk X4S R7800

Brands by name

Popular brands

NETGEAR Nighthawk X4S R7800, User Manual

Search results

Summary of Contents for Nighthawk X4S R7800

Reviews:

Related manuals for Nighthawk X4S R7800

Brands by name

Popular brands