NETGEAR Nighthawk X4S R7800 User Manual Download Page 11

Page: 11 / 160

Description

LED

The LED color indicates the speed: white for Gigabit Ethernet connections and amber for 100 Mbps or
10 Mbps Ethernet connections.

•

Solid. A powered-on device is connected to the Ethernet port.

•

Blinking. The port is sending or receiving traffic.

•

Off. No device is connected to this Ethernet port.

Ethernet ports 1–4

Pressing this button for two seconds turns the 2.4 GHz and 5 GHz WiFi radios on and off.

If this LED is lit, the WiFi radios are on. If this LED is off, the WiFi radios are turned off and you cannot
use WiFi to connect to the router.

WiFi On/Off button with
LED

This button lets you use WPS to join the WiFi network without typing the WiFi password. The WPS LED
blinks white during this process and then lights solid white.

WPS button with LED

You can use the LED On/Off switch on the rear panel of the router to turn the LEDs on the top of the router on or
off. See

Turn the LEDs On or Off

on page 12.

Rear Panel

The rear panel connections and buttons are shown in the following figure.

Figure 3. Router rear panel

Pressing the Reset button restores the factory settings. See

Factory Settings

on page 158>

Hardware Setup

Nighthawk X4S AC2600 Smart WiFi Router

Summary of Contents for Nighthawk X4S R7800

































































































































































Search results

Summary of Contents for Nighthawk X4S R7800

Reviews:

Related manuals for Nighthawk X4S R7800

Brands by name

Popular brands

NETGEAR Nighthawk X4S R7800, User Manual

Search results

Summary of Contents for Nighthawk X4S R7800

Reviews:

Related manuals for Nighthawk X4S R7800

Brands by name

Popular brands