NETGEAR AC1450 User Manual Download Page 57

Page: 57 / 128

ReadySHARE Printer

AC1450 Smart WiFi Router

Select the printer and click the

Connect

button.

Once the connection is established, the status changes to Manually connected by

xxx

You can click the

Disconnect

button at any time to release the connection. The status

then changes to Available.

After you click the Connect button once on each computer in the network, the utility on

each of them manages the printing queue and handling. The status of the printer is

Available on all of the computers.

•

When the status is Available, you can use the USB printer.

•

When the status is Manually connected by

xxx

, only the

xxx

computer can use the

printer. Other network devices must wait until the

xxx

computer has released the

connection, or until the connection times out (the default time-out value is 30
seconds).

Summary of Contents for AC1450

































































































































Search results

Summary of Contents for AC1450

Reviews:

Related manuals for AC1450

Brands by name

Popular brands

NETGEAR AC1450, User Manual

Search results

Summary of Contents for AC1450

Reviews:

Related manuals for AC1450

Brands by name

Popular brands