Neteon GW5120 User Manual Download Page 8

Page: 8 / 77

User’s Manual

Wireless Serial Server GW5120

2.4. Installation Procedures

Prepare necessary cables, DC power adapter and serial connector.

Place GW5120 under the access point signal coverage area, or connect GW5120 to Ethernet
cable with RJ45 connector.

Connect GW5120 serial port to a serial device; make sure the connector and wiring of RS-232
is correct.

Plug in GW5120 to DC 9-48V power source (with DC-jack or 3-pin terminal bock connector),
buzzer will beep and the RUN LED will blink if GW5120 functions normally. For LED Status
sees Appendix D4.

Use

SerialManager

utility from the product CD to check the status of GW5120. If it starts up

successfully, IP and MAC address of GW5120 will be displayed. IP address, subnet mask and
gateway can also be set by

SerialManager

Summary of Contents for GW5120








































































Search results

Summary of Contents for GW5120

Reviews:

Related manuals for GW5120

Brands by name

Popular brands

Neteon GW5120, User Manual

Search results

Summary of Contents for GW5120

Reviews:

Related manuals for GW5120

Brands by name

Popular brands