NetApp FAS2600 Manual Download Page 714

Page: 714 / 786

3. Align the edges of the replacement boot media with the boot media socket, and then gently push it into the

socket.

4. Check the boot media to make sure that it is seated squarely and completely in the socket.

If necessary, remove the boot media and reseat it into the socket.

5. Push the boot media down to engage the locking button on the boot media housing.

6. Reinstall the controller module lid by aligning the pins on the lid with the slots on the motherboard carrier,

and then slide the lid into place.

Step 3: Transfer the boot image to the boot media

You can install the system image to the replacement boot media using a USB flash drive with the image
installed on it. However, you must restore the

var

file system during this procedure.

Before you begin

• You must have a USB flash drive, formatted to FAT32, with at least 4GB capacity.

• A copy of the same image version of ONTAP as what the impaired controller was running. You can

download the appropriate image from the Downloads section on the NetApp Support Site

◦

If NVE is enabled, download the image with NetApp Volume Encryption, as indicated in the download
button.

◦

If NVE is not enabled, download the image without NetApp Volume Encryption, as indicated in the
download button.

• If your system is a stand-alone system you do not need a network connection, but you must perform an

additional reboot when restoring the var file system.

Steps

1. Align the end of the controller module with the opening in the chassis, and then gently push the controller

module halfway into the system.

2. Recable the controller module, as needed.

3. Insert the USB flash drive into the USB slot on the controller module.

Make sure that you install the USB flash drive in the slot labeled for USB devices, and not in the USB
console port.

4. Push the controller module all the way into the system, making sure that the cam handle clears the USB

flash drive, firmly push the cam handle to finish seating the controller module, and then push the cam
handle to the closed position.

The node begins to boot as soon as it is completely installed into the chassis.

5. Interrupt the boot process to stop at the LOADER prompt by pressing Ctrl-C when you see Starting

AUTOBOOT press Ctrl-C to abort….

If you miss this message, press Ctrl-C, select the option to boot to Maintenance mode, and then halt the
node to boot to LOADER.

6. Although the environment variables and bootargs are retained, you should check that all required boot

environment variables and bootargs are properly set for your system type and configuration using the

printenv bootarg name

command and correct any errors using the

setenv variable-name

<value>

command.

712

Summary of Contents for FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAS2600

Reviews:

Related manuals for FAS2600

Brands by name

Popular brands

NetApp FAS2600, Manual

Search results

Summary of Contents for FAS2600

Reviews:

Related manuals for FAS2600

Brands by name

Popular brands