neno LEADX Ultra Assembly And Operating Instructions Manual Download Page 27

Page: 27 / 108

NENO LEADX Ultra Manual

Seite | 27

2.5.3 Locking nut and diaphragm coupling

Article
Nr.

Description

Quantity

FK storage block (fixed bearing)

FK locking nut

Manually screw the FK lock nut onto the end of the ball screw, which is located at the fixed end.

Tighten the grub screw on the FK lock nut to secure the FK lock nut.

Article
Nr.

Description

Quantity

FK storage block (fixed bearing)

Diaphragm coupling

Place the diaphragm coupling on the fixed end of the ball screw. Tighten the grub screw on the
diaphragm coupling to secure it to the ball screw.

Screws are very sensitive to tightening torque. Avoid tightening them too tightly, otherwise you
could destroy the screw head.

Summary of Contents for LEADX Ultra













































































































Search results

Summary of Contents for LEADX Ultra

Reviews:

Related manuals for LEADX Ultra

Brands by name

Popular brands

neno LEADX Ultra, Assembly And Operating Instructions Manual

Search results

Summary of Contents for LEADX Ultra

Reviews:

Related manuals for LEADX Ultra

Brands by name

Popular brands