Necta KIKKO ES6, Installation, Use And Maintenance Manual

Page: 26 / 76

© by NECTA VENDING SOLUTIONS SpA
22
02-2004 184 02
POWDER DOSE
The powder dose, expressed in grams, can be set for each
selection button and therefore each product assigned to it;
the display indicates the name of the product being se-
lected.
It also possible to program the doses of a product “Glo-
bally”, i.e. setting all selections with a single operation.
DOSER DEVICE FLOW
For correct conversion of product dose values, the flow
rate of the single doser units, expressed in g/s, can be set
to calculate the amount of powder to be dispensed.
ACCESSORIES
Dispensing of sugar, stirrer and cup can be enabled or
disabled for each single selection button.
SELECTION STATUS
Each single selection button can either be enabled or
disabled.
BUTTON/SELECTION ASSOCIATION
This function is used to change the order of the selections
associated to the push-button panel.
The display will indicate in a sequence the list of available
selections and when pressing the target button the asso-
ciation is stored.
SELECTION POSITION
When the display shows this function, it will be possible to
read the selection to which the pressed button is assigned.
PRODUCT CODE
This function is used for assigning a 4-digit identification
code to each selection for processing the statistics.
VENDING MACHINE PARAMETERS
TEMPERATURE
This function is used for setting the operating temperature,
expressed in °C, of the boilers installed in the machine.
After selecting the boiler, press the confirm button “ ”, the
temperature value on the display will start blinking and can
be modified as necessary.
TANK
For defining whether the machine water supply is from the
mains or from an internal tank.
MIXER HEATING
If the function is enabled and no selections were made in
the last 3 minutes, a small amount of hot water is dis-
pensed into the milk or instant coffee mixers before dis-
pensing short instant coffee, instant coffee with milk and
espresso coffee with milk.
MIXERS COOLING
If the function is enabled and no cold drink selections were
made in the last 5 minutes, a small amount of cold water
is dispensed into the cold drink mixers before dispensing.
FAST CYCLES
When this function is enabled, some of the time that is
useful for improving the drink quality is eliminated.
for instant selections
- all of the products that compose the drink are dispensed
at the same time;
- the “post-whipping” time is eliminated.
for espresso selections
- pre-brewing is not performed;
- the pump, used to increase the boiler pressure after an
instant drink selection, is not started;
- the “post-whipping” time is eliminated.
SETTING THE REGENERATION COUNTER
It is possible to display the message
“Regenerate the water softener”
upon accessing “filler” mode after a programmable number
of drinks dispensed.
CUP SENSOR
The machine can be fitted with a “cup sensor” composed
of photocell that detects the presence of an object in the
dispensing compartment.
When the function is enabled, if an object is detected in the
dispensing compartment, a cup is not released and the
display indicates the message “Without cup”.
It is also possible to define whether, after two attempts to
release a cup without the photocell detecting any objects
in the dispensing compartment; the failure should lock the
machine or leave it to operate using a ceramic cup.
RETAINED SLIDER/COMPARTMENT LAMP
The machine can be fitted with a magnet that holds the
drink dispensing compartment slider lifted for certain length
of time. The time starts from the sound signal at the end of
dispensing and can be programmed between 0 and 15
seconds. In any case, the slider is released at the start of
the next selection.
If the cup sensor is fitted, the slider is retained for a
programmable time (0 to 30 seconds; 2 by default) from
picking up the drink.
Parallel to the magnet, a lighting lamp can be fitted inside
the dispensing compartment.
COLUMN ROTATION DELAY
This function is used to set the delay time in stopping the
cup column rotation in order to compensate any inertia due
to the cup type.
MOK-CAP WASH
This function is not active in this model.