NEC NEASCOT-P65 User Manual Download Page 312

Page: 312 / 317

CHAPTER 6 JTAG BOUNDARY SCAN

PRELIMINARY

NEC confidential and Proprietary

313

6.5 TAP Controller Operation

The TAP controller operates as follows.

The state of the controller is changed by either of (1) and (2) below.

(1) Rising edge of JCK pin signal

(2) JRST_B pin input

The TAP controller generates signals that control the operations of the bypass register, boundary scan register, and

instruction register defined by the IEEE1149.1 JTAG Boundary Scan Standard (see Figures 6-4 and 6-5).

The JDO pin output buffer and the peripheral circuit that selects a register whose contents are to be output to the

JDO pin are controlled as shown in Table 6-1. The JDO pin defined in this table changes at the falling edge of the

JCK pin signal after it has entered each state.

Table 6-1. Operation in Each Controller State

Controller State

Selected Register to Be Driven to JDO Pin

JDO Pin Driver

Test-Logic-Reset

Run-Test/Idle

Select-DR-Scan

Select-IR-Scan

Capture-IR

Undefined

High impedance

Shift-IR

Instruction register

Active

Exit1-IR

Pause-IR

Exit2-IR

Update-IR

Capture-DR

Undefined

High impedance

Shift-DR

Data register (boundary scan register, bypass register)

Active

Exit1-DR

Pause-DR

Exit2-DR

Update-DR

Undefined

High impedance

Summary of Contents for NEASCOT-P65






























































































































































































































































































































Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands

NEC NEASCOT-P65, User Manual

Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands