NEC NEASCOT-P65 User Manual Download Page 119

Page: 119 / 317

CHAPTER 4 INTERFACES

PRELIMINARY

NEC confidential and Proprietary

119

(2) TAG

The

PD98413 supports modes in which a one-word space is inserted in the first word of a cell as a function to

assist the ATM device to append TAG (label) to each cell. In this manual, these modes are referred to as modes

with and without TAG. The TAG mode is set to the MDAPIT and MDAPIR registers.

Table 4-2. Mode of TAG

Mode without TAG (Default)

Mode with TAG

Transmission

The word indicated by the high level of

TXSOC is input as the first word of a

cell.

The word in the cycle next to that in

which a word indicated by the high level

of TXSOC is input as the first word of a

cell. The

PD98413 ignores the first

word (TAG).

Reception

RXSOC is driven high when the first

word of a cell is output.

One word of TAG space is inserted

before the first word of a cell, and

RXSOC is driven high when the TAG

space is output.

The user can set any TAG value added to the receive cell in the IADRR register. The

PD98413 sends the

receive cell to ATM interface with the TAG value set to the IADRR register.

4.2.3 Transmit

operation

The

PD98413 supports both the direct status indication mode and the status polling mode (Multi-PHY operation

with 1 TXCLAV).

(1) Direct status indication

The

PD98413 implements a dedicated TXCLAV signal for each of the ports. TXCLAV0 corresponds to the

port0, while TXCLAV3 corresponds to the port3.

The ATM device can send a cell to the

PD98413 only when the port has indicated to the ATM device that it is

ready to receive at least one complete cell. The

PD98413 indicates transmit cell buffer available information to

the ATM device. The TXCLAV0-3 are not applicable on the first cycle after TXSOC is asserted, on this cycle, the

PD98413 keeps the status before the transfer is started. The

PD98413 will deassert TXCLAV unless it can

accept at least one cell (after the currently transferred cell) from the ATM device. Once the TXCLAV0-3 has

been asserted, it will have to stay asserted until the clock edge after assertion of the next TXSOC on that

particular port. The FIFO availability information indicated by TXCLAV is programmable by the FTHT register.

The port to which the next cell will be sent will be selected by TXADDR[1:0] during the clock cycle before

TXENB_B is asserted. This signal will be decoded by the

PD98413 and the specified port will be ready to

receive cell data from the ATM device as soon as the TXENB_B is asserted.

The following figure shows an example of the transmit timing in the direct status indication.

Summary of Contents for NEASCOT-P65






























































































































































































































































































































Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands

NEC NEASCOT-P65, User Manual

Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands