NEC NEASCOT-P65 User Manual Download Page 20

Page: 20 / 317

CHAPTER 2 PIN FUNCTION

PRELIMINARY

NEC confidential and Proprietary

(2/2)

Pin Name

Serial No.

Address No.

I/O Level

Function

TXCLK

LVTTL

Transmit clock input.

This pin inputs the clock, up to 104 MHz, used to transfer

transmit data.

TXDATA[31:0]

LVTTL

Transmit data input bus.

These pins form a 32-bit data bus through which transmits

cell data is input. The

PD98413 samples the data on this

bus at the rising edge of TXCLK.

TXSOC

LVTTL

Transmit start of cell input.

This pin is inputted a signal that indicates the start position

of a transmit cell. The

PD98413 recognizes the clock cycle

in which TXSOC is high as the first word of a cell.

TXENB_B

LVTTL

Transmit enable signal input.

This signal indicates that the ATM device has output valid

transmit cell data to TXDATA. The

PD98413 samples

TXENB_B at the rising edge of TXCLK. If TXENB_B is low,

it loads the data on TXSOC and TXDATA to the transmit

FIFO at the edge of TXCLK. If TXENB_B is high, the data

on TXSOC and TXDATA is not loaded to the transmit FIFO.

TXCLAV0-3

LVTTL

Transmit cell buffer available.

This signal posts notification of the vacancy of the transmit

FIFO to the ATM device

If the number of cells stored in the

transmit FIFO has reached the threshold value set by the

APHIGH[7:0] bits of the FTHT1 register, the

PD98413

drives TXCLAV low. The subsequent cells are dropped and

the

PD98413 reports an overflow of the transmit FIFO.

TXCLAV0 corresponds to PORT0, while TXCLAV3

corresponds to PORT3.

TXPRTY

LVTTL

(Internal

pull-up)

Transmit data path parity.

This pin inputs the odd parity bit of the data input to

TXDATA. The

PD98413 calculates parity based on the

input data and parity bit. If it detects an error, it sets the

PARE bit of the APIET register to report the error. An even

parity can be also used depending on the setting of the

MDAPIT register.

TXADDR[1:0]

LVTTL

Transmit address input.

These pins are used to input a port address for data

transmission.

Summary of Contents for NEASCOT-P65






























































































































































































































































































































Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands

NEC NEASCOT-P65, User Manual

Search results

Summary of Contents for NEASCOT-P65

Reviews:

Related manuals for NEASCOT-P65

Brands by name

Popular brands