NEC N8100-1950F Maintenance Manual Download Page 95

Page: 95 / 166

4. RAID System Configuration

Express5800/R120d-1E, R120d-2E Maintenance Guide

Chapter 2 Convenient Features

RAID System Configuration

This section describes the RAID configuration utility, the LSI Software RAID Configuration Utility.

Because this utility resides in LSI Embedded MegaRAID, its operation is independent of the OS.

Jumper settings on the motherboard required to use the RAID controller (LSI Embedded MegaRAID) is
described in the images below.

4.1

Running the LSI Software RAID Configuration Utility

When the message below appears on the POST screen after turning on the server, press the <Ctrl> + <M>
keys or <Enter> key. The LSI Software RAID Configuration Utility starts.

Press Ctrl-M or Enter to run LSI Software RAID Configuration Utility

Tips

If you failed to perform key operation as described above and the following screen did not

appear, restart the server and retry.

RAID Configuration Jumper (RAID_KEY1)

Enabled

Disabled

(Factory setting)

Summary of Contents for N8100-1950F







































































































































































Search results

Summary of Contents for N8100-1950F

Reviews:

Related manuals for N8100-1950F

Brands by name

Popular brands

NEC N8100-1950F, Maintenance Manual

Search results

Summary of Contents for N8100-1950F

Reviews:

Related manuals for N8100-1950F

Brands by name

Popular brands