background image

English

English-2

Safety Precautions and Maintenance

Refer to the manual of the monitor.

Canadian Department of Communications Compliance Statement

DOC:  This Class B digital apparatus meets all requirements of the Canadian Interference-Causing 

Equipment Regulations.

FCC Information

  This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.

  • Increase the separation between the equipment and receiver.

  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

  • Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional 
suggestions.

The user may fi nd the following booklet, prepared by the Federal Communications Commission, helpful: 
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. 
Government Printing Offi ce, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Summary of Contents for MPD-DTi
















Reviews: