NEC Express5800/R120f-1M Maintenance Manual Download

Page: 80 / 180

1. System BIOS

Express5800/R120f-1M, R120f-2M Maintenance Guide

Chapter 2 Useful Features

For details about the options, see the table below.

Option

Parameter

Description

Serial Port A Settings

−

Serial Port A

Disabled

[Enabled]

Enable or disable serial port A

Serial A Base I/O

[3F8h]

2F8h

3E8h

2E8h

Specify the base I/O address for serial port A.

Serial A Interrupt

[IRQ 4]

IRQ 3

Specify the interrupt for serial port A

Serial Port B Settings

−

Serial Port B

Disabled

[Enabled]

Enable or disable serial port B

Serial B Base I/O

3F8h

[2F8h]

3E8h

2E8h

Specify the base I/O address for serial port B

Serial B Interrupt

IRQ 4

[IRQ 3]

Specify the interrupt for serial port B

Auto-Shutdown

[Disabled]
Enabled

Enable or disable auto shutdown for the serial

port. To specify "Enabled", a device that

supports this feature must be connected. If the

connected device does not support this

feature, the serial ports will fail to return from

halt state.

Console Redirection Settings

−

BIOS Redirection Port

[Disabled]

Serial Port A

Serial Port B

Enable or disable console redirection for a

specified serial port. Specifying "Serial Port A"

or "Serial Port B" allows direct connection via

a terminal unit such as NEC ESMPRO

Manager. The screen size of the terminal unit

must be 80 x 25. The option items shown

below are displayed.

Terminal Type

[VT100+]

VT-UTF8

PC-ANSI

Select the terminal type.

Baud Rate

9600

19200

57600

[115200]

Specify the baud rate.

Data Bits

[8]

Specify the data bit width.

Parity

[None]

Even

Odd

Specify the parity type.

Stop Bits

[1]

Specify the number of stop bits.

Flow Control

None

[Hardware RTS/CTS]

Specify the flow control method.

Continue C.R. after POST

Disabled

[Enabled]

Select whether to continue console redirection

after completion of POST.

[ ]: Factory setting

Summary of Contents for Express5800/R120f-1M





















































































































































































Search results

Summary of Contents for Express5800/R120f-1M

Reviews:

Related manuals for Express5800/R120f-1M

Brands by name

Popular brands

NEC Express5800/R120f-1M, Maintenance Manual

Search results

Summary of Contents for Express5800/R120f-1M

Reviews:

Related manuals for Express5800/R120f-1M

Brands by name

Popular brands