NEC Express5800/R120f-1M Maintenance Manual Download

Page: 142 / 180

1. POST Error Message

Express5800/R120f-1M, R120f-2M Maintenance Guide

142

Chapter 3 Appendix

(1) Error messages

Error Message

Cause

Solution

8000

System variable is

corrupted.

Illegal setup information of

BIOS was detected.

Start BIOS Setup Utility (SETUP), and then

execute

Load Setup Defaults

and specify the

necessary settings.

If the same error is detected repeatedly in spite of

re-setting, contact your sales representative.

8001

Real time clock error

Real time clock error was

detected.

Start SETUP, and then specify the correct date

and time.

If the same error is detected repeatedly in spite of

re-setting, contact your sales representative.

8002

Check date and time settings

Incorrect date and time set on

real time clock was detected.

8003

System battery is dead -

Replace and run SETUP

The battery for storing system

settings is dead.

Contact your sales representative. (After the

replacement, start SETUP, and then specify the

correct settings.)

8005

Previous boot incomplete -

Default configuration used

The previous POST processing

did not finish.

Use SETUP to specify the correct settings.

8006

System configuration data

cleared by Jumper.

The setup utility settings were

cleared using the jumper.

Follow the steps described in

Chapter 1 (7.

Resetting and Clearing the Server).

Start SETUP, and then setup each item again.

If the same error is detected repeatedly in spite of

re-setting, contact your sales representative.

This error message also appears when lithium

battery is removed.

8007

SETUP Menu Password cleared

by Jumper.

The setup utility password was

cleared using the jumper.

8020

BIOS update error.

BIOS update failed.

Try BIOS update again.

If the same error is detected repeatedly, contact

your sales representative.

8021

Recovery jumper is set, but

recovery images is not

found.

Recovery jumper is set, but

recovery images is not found.

Contact your sales representative.

8800

DXE_NB_ERROR

An error was detected during

initialization of chipset.

8801

DXE_NO_CON_IN

An error was detected during

initialization of console.

8802

DXE_NO_CON_OUT

8803

PEI_DXE_CORE_NOT_FOUND

A flash ROM is corrupt.

8804

PEI_DXEIPL_NOT_FOUND

8805

DXE_ARCH_PROTOCOL_NOT_AVA

ILABLE

8806

PEI_RESET_NOT_AVAILABLE

The system was not reset

correctly.

8807

DXE_RESET_NOT_AVAILABLE

Follow the steps described in

Chapter 1 (7.

Resetting and Clearing the Server).

Start SETUP, and then setup each item again.

If the same error is detected repeatedly in spite of

re-setting, contact your sales representative.

8808

DXE_FLASH_UPDATE_FAILED

The Flash ROM was not written

to correctly.

Contact your sales representative.

8830

PEI_RECOVERY_NO_CAPSULE

The Flash ROM was not

recovered correctly.

8831

PEI_RECOVERY_PPI_NOT_FOUN

8832

PEI_RECOVERY_FAILED

9000

Unsupported CPU detected

An unsupported CPU was

detected.

9001

Unsupported CPU detected on

CPU #1

9002

Unsupported CPU detected on

CPU #2

9021

Unsupported CPU Speed

detected on CPU #1

A CPU of which clock speed is

unsupported was detected.

9022

Unsupported CPU Speed

detected on CPU #2

Summary of Contents for Express5800/R120f-1M





















































































































































































Search results

Summary of Contents for Express5800/R120f-1M

Reviews:

Related manuals for Express5800/R120f-1M

Brands by name

Popular brands

NEC Express5800/R120f-1M, Maintenance Manual

Search results

Summary of Contents for Express5800/R120f-1M

Reviews:

Related manuals for Express5800/R120f-1M

Brands by name

Popular brands