manualshive.com logo in svg

NEC Express5800/R120f-1M, Maintenance Manual, Page: 120 / 180

Share
Download
NEC Express5800/R120f-1M Maintenance Manual Download Page 120

3. Flash FDD 

 

Express5800/R120f-1M, R120f-2M  Maintenance Guide 

120 

Chapter 2    Useful Features 

3.

 

Flash FDD 

Flash FDD is a device that is compatible with a floppy disk drive. 

One Flash FDD can be connected to a USB connector of this server. If another USB or floppy disk drive is 
connected to this server, be sure to remove it. 

 

 

CAUTION

 

 

 

Be extremely careful not to lose Flash FDD or have it stolen. 
If Flash FDD is lost, stolen, misappropriated, or fraudulently obtained, there is a risk of 
leaking confidential information to a third party. NEC assumes no responsibility for 
damages caused by leaking confidential information in this way. 

 

If you want to change the write protection, remove Flash FDD from the server and change the write protection 
switch, and then connect it again. 

 

Note 

Be careful not to accidentally flip the write protection switch while connecting Flash FDD to 

or removing it from the server. 

 

 

3.1

 

Notes on Using Flash FDD 

Do not use Flash FDD to back up data. Flash FDD can be used for a temporary data only. 

 

3.1.1

 

Compensation for recorded data 

NEC will not pay compensation for data recorded on Flash FDD even if the data is lost. 

 

3.1.2

 

Handling Flash FDD 

 

•

  Flash FDDs are consumables. If Flash FDD causes an error, exchange to a new Flash FDD. 

•

  Do not turn off the server while the access LED of Flash FDD is blinking.   

•

  Flash FDD cannot be connected to a USB hub. Directly connect Flash FDD to the server. 

•

  Before touching Flash FDD, discharge static electricity from your body by touching a nearby metal object 

such as a doorknob or aluminum frame. 

•

  Do not disassemble Flash FDD. 

•

  Do not apply a strong force to Flash FDD. 

•

  Do not place Flash FDD in an area directly exposed to sunlight or near a heater. 

•

  Do not handle Flash FDD while eating, drinking, or smoking. Also, avoid contact with thinner, alcohol, or 

other corrosive substances. 

•

  Carefully connect Flash FDD to the server. 

•

  Do not move the server while Flash FDD is connected to USB connector.   

•

  Remove Flash FDD from the server after use.

 

 

Summary of Contents for Express5800/R120f-1M





















































































































































































Reviews:

No comments