NEC Express5800/R120f-1M Maintenance Manual Download Page 149

Page: 149 / 180

1. POST Error Message

Express5800/R120f-1M, R120f-2M Maintenance Guide

149

Chapter 3 Appendix

Error Message

Cause

Solution

C10C

BMC update firmware

corrupted.

An illegality was detected while

updating BMC firmware.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the same error

is detected repeatedly, contact your sales

representative.

C10D

Internal Use Area of BMC FRU

corrupted.

An illegality was detected in

FRU containing the device

information.

C10E

BMC SDR Repository empty.

An error was detected on BMC

SDR.

C10F

IPMB signal lines do not

respond.

Failure of Satellite Management

Controller was detected.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the same error

is detected repeatedly, contact your sales

representative.

C110

BMC FRU device failure.

An error was detected in FRU

that contains device

information.

C111

BMC SDR Repository failure.

Failure was detected in SROM

that stores the SDR.

C112

BMC SEL device failure.

Device failure was detected in

BMC SEL.

C113

BMC RAM test error.

An error was detected in BMC

RAM.

C114

BMC Fatal hardware error.

A hardware error was detected

in BMC.

C115

Management controller

not responding

Management controller does

not respond.

Update the BMC firmware.

If the same error is detected repeatedly, contact

your sales representative.

C116

Private I2C bus not

responding.

Private I2C bus does not

respond.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the same error

is detected repeatedly, contact your sales

representative.

C117

BMC internal exception

BMC internal error was

detected.

C118

BMC A/D timeout error.

BMC A/D timeout error was

detected.

C119

SDR repository corrupt.

BMC error or illegal SDR data

was detected.

C11A

SEL corrupt.

BMC error or illegal system

event log data was detected.

C11B

BMC Mezzanine card is not

found.

BMC Mezzanine card is not

installed.

Contact your sales representative.

C11C

BMC Mezzanine partition is

invalid.

A format error was detected in

BMC Mezzanine card.

C11D

BMC is in Forced Boot Mode.

Detected that BMC is in Forced

Boot Mode.

Unplug the power cord, wait for at least 30

seconds, then restart the server. At that time,

check the jumper switch setting on motherboard.

If the same error is detected repeatedly, contact

your sales representative.

C11E

Communication with BMC was

failed in previous boot

Communication with BMC was

failed in previous boot

Unplug the power cord, wait for 30 seconds, and

reboot the server. If the same error is detected

repeatedly, contact your service representative.

C11F

Backup Data of BMC Mezzanine

card has corrupted.

Inconsistency was found on

BMC mezzanine card.

Contact your service representative.

C120

BMC Runtime FW corrupted.

An error occurred on BMC

Runtime FW.

Disconnect the power cord, wait for at least 30

seconds, and then reboot the system. If the same

error is detected again, contact your maintenance

service company.

C121

BMC Force Update FW corrupted.

An error occurred on BMC

Force Update FW.

C122

BMC Configuration area

corrupted.

An error occurred on BMC

Configuration area.

C123

BMC eMMC inaccessible.

Failed to access to BMC

eMMC.

C125

BMC eMMC mode error.

BMC eMMC mode error

C126

BMC eMMC partition corrupted.

An error occurred on BMC

eMMC partition.

C127

BMC eMMC format corrupted.

A format error occurred on BMC

eMMC.

C128

BMC is in Update Mode.

BMC is in update mode.

Summary of Contents for Express5800/R120f-1M





















































































































































































Search results

Summary of Contents for Express5800/R120f-1M

Reviews:

NEC Express5800/R120f-1M, Maintenance Manual, Page: 149 / 180

Search results

Summary of Contents for Express5800/R120f-1M

Reviews: