NEC Express5800/B120a-d User Manual Download

Page: 95 / 294

Installing the Operating System with Express Setup 5-23

The procedure to set PAE option

If your 32-bit system has a memory capacity in excess of 4GB, setting PAE option will enable the
system to be installed with over 4GB of memory.

IMPORTANT:

"PAE option" is not supported on Windows Server

2008 Standard Edition.

In Windows Server 2008 system, the PAE option can be set by using Bcdedit.exe.

The setting procedure is as follows.

Click [Run] on [Start] menu.

Type "cmd.exe" in the [Open:] box to start command prompt.

Execute following command line.

bcdedit /set pae forceenable

Reboot the system.

The setting mentioned above enables after reboot.

Execute following command line on command prompt.

bcdedit

Confirm "pae ForceEnable" exists in "Windows boot loader".

The setting for PAE option is now completed.

Refer following site about Bcdedit.exe.

"Boot Configuration Data Editor Frequently Asked Questions"

http://technet.microsoft.com/en-us/library/cc721886.aspx

Setting for Solving Problems

Setup your computer in advance so that it can recover from any trouble precisely and as soon as
possible when it should occur.

For more information, refer to Page 5-42.

Summary of Contents for Express5800/B120a-d







































































































































































































































































































Search results

Summary of Contents for Express5800/B120a-d

Reviews:

Related manuals for Express5800/B120a-d

Brands by name

Popular brands

NEC Express5800/B120a-d, User Manual

Search results

Summary of Contents for Express5800/B120a-d

Reviews:

Related manuals for Express5800/B120a-d

Brands by name

Popular brands