NEC Express5800/B120a-d User Manual Download

Page: 107 / 294

Installing the Operating System with Express Setup 5-35

10.

Enter the user information and client license mode.

[Enter basic parameters] steps are displayed. Confirm the parameters, modify if necessary,
and then click [Next].

NOTE:

Even if you do not input value into "Administrator password",

"Confirm password", "

zzzzzz

" is displayed.

11.

Enter the setting of the network protocol.

[Enter Network Protocol] steps are displayed. Confirm the parameters, modify if
necessary, and then click [Next].

Summary of Contents for Express5800/B120a-d







































































































































































































































































































Search results

Summary of Contents for Express5800/B120a-d

Reviews:

Related manuals for Express5800/B120a-d

Brands by name

Popular brands

NEC Express5800/B120a-d, User Manual

Search results

Summary of Contents for Express5800/B120a-d

Reviews:

Related manuals for Express5800/B120a-d

Brands by name

Popular brands