NEC EXP292 User Manual Download Page 97

Page: 97 / 153

1. Installing Internal Optional Devices

Express5800/T120d User’s Guide

Chapter 2 Preparations

1.15

Fixed Type Hard Disk Drive

This section describes installation procedure for optional fixed type hard disk drive.

Important

Do not use unsupported hard disk drive.

1.15.1

Installation

Install fixed type hard disk drive in the following procedure.

Refer to steps 1 to 7 in Chapter 2 (1.3 Overview of Installation and Removal) for preparations.

Secure a hard disk drive to HDD tray of

3.5-inch Fixed HDD cage using four screws.

Secure the HDD tray with hard disk drive to

the server using two screws.

Install hard disk drives starting from bottom

bay.

Important

To maintain cooling efficiency, install HDD trays to which no hard disk drive

is mounted.

Summary of Contents for EXP292


























































































































































Search results

Summary of Contents for EXP292

Reviews:

Related manuals for EXP292

Brands by name

Popular brands

NEC EXP292, User Manual

Search results

Summary of Contents for EXP292

Reviews:

Related manuals for EXP292

Brands by name

Popular brands