NEC EXP292 User Manual Download Page 42

Page: 42 / 153

4. Names and Functions of Parts

Express5800/T120d User’s Guide

Chapter 1 General Description

4.7.7

LEDs for LAN connectors

The three LAN connectors provided at the rear of the server have two LEDs each.

•

LINK/ACT LED(

This LED indicates the state of the LAN port. LINK LED lights green when the server and hub are
powered and properly connected. ACT LED flashes green when the port is transmitting or receiving data.

If the LED does not turn on in LINK state, check the cable or connection.

•

SPEED LED(

This LED indicates which network interface is used.

−

Two onboard LANs (

support 1000BASE-T, 100BASE-TX, and 10BASE-T.

The LED indicates which network interface is being used.

•

Amber: Operating with 1000BASE-T

•

Green: Operating with 100BASE-TX

•

OFF:

Operating with 10BASE-T

−

Management LAN (

supports 100BASE-TX and 10BASE-T.

The LED indicates which network interface is being used.

•

Green: Operating with 100BASE-TX

•

OFF:

Operating with 10BASE-T

LAN1
Connector

LAN2
Connector

Management
LAN Connector

LINK/ACT
LED

SPEED
LED

LINK/ACT
LED

SPEED
LED

LINK/ACT
LED

SPEED
LED

Summary of Contents for EXP292


























































































































































Search results

Summary of Contents for EXP292

Reviews:

Related manuals for EXP292

Brands by name

Popular brands

NEC EXP292, User Manual

Search results

Summary of Contents for EXP292

Reviews:

Related manuals for EXP292

Brands by name

Popular brands