NEC 910i Installation And User Manual Download Page 14

Page: 14 / 106

1-12

Installation

Upgrading the Firmware

Use these instructions when upgrading the Firmware ROM in your

910i

Cordless Telephone Base Unit. The

new ROM in your upgrade kit is a static-sensitive component. Be sure to follow the instructions below
carefully.

Failure to follow proper anti-static precautions could damage your new firmware.

Removing Old Firmware EPROM:

1. Unplug the base unit from the line cord.
2. Attach a grounded wrist strap to your wrist and a grounded metal object (such as

CEU ground).

3. Remove the screws from the bottom of the base unit and remove the cover.
4. Using an IC puller, carefully remove the old Firmware ROM. Be careful not to rock

the ROM or bend the pins during removal.

Installing New Firmware ROM:

1. Remove the new Firmware ROM from the anti-static sleeve.
2. Following the illustration at right, carefully install the new ROM in the base.

●

Pay careful attention to line up the notch in the ROM with the notch in
its socket. The notch should be on the edge that denotes pin “1”

●

Do not bend any pins when plugging in the ROM.

3. Discard the old ROM.
4. Replace the cover on the base unit and reinstall the four screws.
5. Plug the line cord into the base unit.

92266 - 2

strap

Key

Grounded wrist

92266 - 1

Grounded wrist

strap

Summary of Contents for 910i











































































































Search results

Summary of Contents for 910i

Reviews:

Related manuals for 910i

Brands by name

Popular brands

NEC 910i, Installation And User Manual

Search results

Summary of Contents for 910i

Reviews:

Related manuals for 910i

Brands by name

Popular brands