NCR 7448 Workstation Hardware User'S Manual Download

Page: 52 / 243

3-4

Chapter 3: Installing Optional Hardware Features

How to Install the International VFD Customer Display

Caution: Do not connect the VFD to a power source that is already powered on.

Integrated Mount International VFD Customer Display (Low
Profile/ Telescope)

Remove the Integrated Display Bracket from the back of the International
VFD Customer Display Cabinet.

Route the display cable through the Telescope Mount, the Low Profile
Mount and the Integrated Display Swivel.

Connect the display cable to the International VFD Customer Display

Remove the Escutcheon on the upper cabinet.

Install the International VFD Customer Display assembly into the upper
cabinet.

Connect the display cable to the RS232 port on the workstation.*

* Note: Cable Routing procedure for 7448 workstation -Hard disk

model

Lay the 7448 workstation on its side.

Summary of Contents for 7448 Workstation




















































































































































































































































Search results

Summary of Contents for 7448 Workstation

Reviews:

Related manuals for 7448 Workstation

Brands by name

Popular brands

NCR 7448 Workstation, Hardware User'S Manual

Search results

Summary of Contents for 7448 Workstation

Reviews:

Related manuals for 7448 Workstation

Brands by name

Popular brands