Napoleon NZ3000 Page 42 Installation And Operating Instructions Manual Download

Page: 42 / 48

W415-0711 / D / 05.09.13

REPLACEMENT PARTS

REF

PART NUMBER

DESCRIPTION

W690-0005

120V THERMOSTAT

W090-0146

BRICK, FRONT LEFT

W090-0147

BRICK, FRONT SIDE (2PC REQUIRED)

W090-0148

BRICK, SIDE (2PC REQUIRED)

W090-0149

BRICK, REAR

W090-0150

BRICK, BASE RIGHT SIDE

W090-0151

BRICK, BASE LEFT SIDE

W090-0156

BRICK, FRONT RIGHT

W018-0116

BAFFLE (2 pc required)

10*

KB-35

VARIABLE SPEED CONTROL - INCLUDING KNOB

11*

W660-0065

HEAT SENSOR

12*

W361-0082

BAFFLE BLANKET

13*

W325-0048

PRIMARY AIR CONTROL HANDLE

W715-0773

ANDIRONS

15*

W385-0334

NAPOLEON® LOGO

W010-1974

SECONDARY AIR MANIFOLD (INCLUDES AIR TUBES)

W720-0126

SECONDARY AIR TUBE

18*

W290-0142

GASKET, SECONDARY AIR MANIFOLD

19*

W450-0028

NUT, HEX BRASS

20*

W010-1896

PILOT TUBE

21*

W615-0106

SPACER

W660-0079

SWITCH, PRESSURE SWING DOOR

23*

W250-0005

BLOWER FILTER

W305-0007

BLOWER GRILL

W290-0148

ANCHOR PLATE GASKET

H336-WI - ARCHED DOUBLE DOORS - WROUGHT IRON FINISH

W300-0103

DOOR GLASS

27*

W562-0058

DOOR GASKET 7/8 x 43" (22.2mm x 1092.2mm)

28*

W562-0002

DOOR GASKET - CENTRE 1/2" x 20" (12.7mm x 508mm)

29*

W010-1933

GLASS & GASKET

W010-1776

LEFT DOOR ASSEMBLY (INCLUDES GLASS, GASKET & HANDLE / LATCH HARDWARE)

W010-1775

RIGHT DOOR ASSEMBLY (INCLUDES GLASS, GASKET & HANDLE / LATCH HARDWARE)

W325-0029

DOOR HANDLE - BIRD CAGE

11.0 REPLACEMENTS

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally
all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE
ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:
•

Model & Serial Number of appliance

•

Installation date of appliance

• Part

number

•

Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR
AUTHORIZED DEALER.

41.1

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

WARNING

Summary of Contents for NZ3000

















































Search results

Summary of Contents for NZ3000

Reviews:

Related manuals for NZ3000

Brands by name

Popular brands

Napoleon NZ3000, Installation And Operating Instructions Manual

Search results

Summary of Contents for NZ3000

Reviews:

Related manuals for NZ3000

Brands by name

Popular brands