background image

W415-0711 / D / 05.09.13

34  

EN

9.6  LIGHTING A FIRE

89.1B

Make sure the air control lever is set to high. You may also open the doors 1" (25.4mm) to 2" (50.8mm) during 
the fi rst fi ve minutes of start-up, if additional air is needed see "COMBUSTION AIR" section.

Remove all source of gasoline or other fl ammable vapours and liquids in the vicinity of this or other 
appliances prior to lighting.

Use plenty of newspaper and kindling to ensure the appliance quickly reaches a proper temperature. Once the 
kindling is burning rapidly, place a few larger pieces of wood onto the fi re.

Tip:

  When fi rst lighting a fi re, if the smoke is not quickly drawn into the chimney, there may be a downdraft or 

cold air in the chimney. By fi rst burning large amounts of crumpled newspaper, the chimney will get heated and 
the smoke will quickly vent up the chimney.

ALWAYS OPERATE THIS APPLIANCE WITH THE DOOR CLOSED AND LATCHED EXCEPT DURING 

START UP AND RE-FUELING OR WHEN USING THE SPARK SCREEN. ALWAYS WEAR GLOVES TO 
PREVENT INJURY. DO NOT LEAVE THE FIRE UNATTENDED WHEN THE DOOR IS UNLATCHED OR 

WHEN USING A SPARK SCREEN AS UNSTABLE WOOD COULD FALL OUT OF THE FIRE CHAMBER 

CREATING A FIRE HAZARD TO YOUR HOME.

NEVER LEAVE CHILDREN UNATTENDED WHEN THERE IS A FIRE BURNING IN THE APPLIANCE.

NEVER USE GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR 

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS APPLIANCE.  KEEP ALL SUCH 

LIQUIDS WELL AWAY FROM THE APPLIANCE.

THIS APPLIANCE HAS NOT BEEN TESTED WITH ANY VENTED OR UNVENTED GAS LOG SET.  TO 

REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL A VENTED OR UNVENTED GAS LOG SET INTO 

THIS APPLIANCE.

BURNING YOUR APPLIANCE WITH THE DOORS OPEN OR AJAR CREATES A FIRE HAZARD THAT 

MAY RESULT IN A HOUSE AND OR CHIMNEY FIRE.

A. 

To start, a brisk fi re is 
required. Roll up some 
newspaper (loosely 
crumpled), light it and place it 
near the appliance fl ue until 
the chimney begins to draw. 

B.

  Cover with dry kindling.

C.

  Fully open the draft control. See 

"

OPERATION

" section. Light 

the paper and leave the door 
slightly ajar (one to two inches) 
until all kindling is burning. 

Summary of Contents for NZ3000

















































Reviews: