EN
WWW.NAKAYAMATOOLS.COM
8
6. Walking
Once the engine stops running, to make the machine walk, please take out the spring pin from tire pin hole and manually push it to walk.
Tire self-walking
H) Spring pin
Driven by the tire driving shaft
Methods for Adjusting Components
1. Adjusting clutch cable
In the case of belt slip while the machine going forward or backward, simply adjust up the adjusting nut.
If the machine can not stop after releasing the clutch handle, simply adjust down the adjusting nut.
2. Adjusting throttle switch cable
In the case of failure to adjust the throttle switch cable in operation, simply adjust the cable tightness as follows; when the throttle switch handle is at
Minimum position, the engine can stop or change into idle speed; on the contrary,when the handle is at maximum position, the engine throttle is with largest
opening.
3. Adjusting the height of operation handlebar
Before operating the machine,adjust the height of the operation handle according to the operation’s height as follows; loosen the locking bolt, move the
handle up or down to proper position, and finally tighten the locking bolt.
J) Adjusting bolt
K) Locking bolt
4. Adjusting the height of cutter fender board
While operating the machine, the height of fender board can adjusted according to the ground condi
-
tion and cutting height.
Cutter Operation
Installing cutter assembly
Take out cutter assembly, attach it to the cutter connecting plate and tighten with bolts, and then adjust the fender board to proper height, and finally fill
with the appropriate lubricant into the drive seat and onto the cutting blade.
Summary of Contents for SM9800
