EN
WWW.NAKAYAMATOOLS.COM
7
Operating instructions
Periodical Inspection
1. Eliminate the abnormal conditions occurring in previous use;
2. Check the fuel for sufficiency;
3. Inspect the engine oil for dirty degree;
4. Check the lubricant for other transmission mechanism of the gearbox;
5. Inspect the air cleaner for lubrication and oil stain;
6. Check the tire for air pressure and wear;
7. Check all sliding parts for lubrication and oil stain;
8. Inspect all parts for their dirty degree;
9. Check all parts for damage as well as loose bolts and nuts;
Note: For the methods for inspecting engine parts,please refer to: Engine Instructions.
Running-in
Caution: The newly purchased machine shall be subject to running-in process;
Therefore,during the first 20 hours in use,don’t run engine to avoid overload running.
Fuel and lubricant filling
The newly purchased machine,before using and starting,must be inspected whether there are fuel and engine oil respectively in the engine fuel tank and
engine oil tank.
1. Fuel Filling:
Fill specified 95# gasoline into the fuel tank.
2. Lubricant Filling
:
a) For engine oil inspection and filling, please refer to (Engine Instructions).
b) Gearboxplease refer to (Engine Instructions).
c) Cutter drive seat (lubricant)
d) Cutting blade (lubricant)
Description of main use
1. Forward
Press the clutch handle and make the belt tighten to go forward:
A) Clutch Handle (forward)
B) Throttle Governor
C) Reverse Handle
D) Choke Switch
2. Reverse
Pull back the reverse handle,make the reverse belt tighten and the driven gear reverse, and then release the handle upon reaching the destination.
3. Speed Changing
Running speed and cutter reciprocating speed can be adjusted through the throttle switch.
4. Steering
Move the operation handle to control the left-right running direction.
5. Stop
A. Release the clutch handle and the machine stops working.
B. Adjust the throttle switch to minimum opening.
C. Turn off the circuit switch and the engine stops running.
B
C
A
Summary of Contents for SM9800
