MW 790031754 Manual Download Page 47 | Manualshive

Page: 47 / 62

background image

47

EN

M1.1.TZHD30S-50S.NLFREN - 15032019

5.4.10 Electrical installation

Wiring should only be done by professional
electricians. Always make sure the machine is
properly earthed.

All wirings in the cabinets should be protected

against direct contact to at least IP2X when

finishing electrical installation.

All exposed conductive parts should be

connected to the protective bonding circuit.

Close and lock the door of cabinets

。

Enough space around the machine and the

cabinets should be kept in order to maintain

conveniently.

The machine should be installed in a workshop

with good illumination and ventilation.

Over-voltage protection device should be

provided by end user on spot.

Check that the voltage and frequency required by

the machine, shown on the machine’s name plate,

correspond to the electric power supply voltage
and frequency.
The circuit breaker shall be installed for supplying
electric power to this machine, in order to protect
people against electrical shock due to indirect
shock

Wiring:

Finish electrical connection according to the
electrical drawings.
The wirings on the spot should refer to the
requirements of Clause 13 (Wring practices) of EN
60204-1:2006.

Checking:

After finishing wiring on the spot, check  the
following items at least:
Check the wirings of machine.
Check the direction of motors and change wiring if
necessary.
Check the components  for defects, such as
loosening or damage.
Check the functions of safety d

ELECTRICAL CONNECTIONS

Electrical installation

WARNING!

• Wiring should only be done by professional electricians� Always make sure the machine is

properly earthed�

• All wirings in the cabinets should be protected against direct contact to at least IP2X when

finishing electrical installation.

• All exposed conductive parts should be connected to the protective bonding circuit�

• Close and lock the door of cabinets�

NOTICE

• Enough space around the machine and the cabinets should be kept in order to maintain

conveniently�

• The machine should be installed in a workshop with good illumination and ventilation�

• Over-voltage protection device should be provided by end user on spot�

Check that the voltage and frequency required by the machine, shown on the machine’s name plate, correspond to the electric

power supply voltage and frequency.

The circuit breaker shall be installed for supplying electric power to this machine, in order to protect people against electrical

shock due to indirect shock.

Wiring:

Finish electrical connection according to the electrical drawings.

The wirings on the spot should refer to the requirements of clause 13 (wiring practices) of EN 60204-1:2006.

Checking:

After finishing wiring on the spot, check the following items at least:

• Check the wirings of machine.

• Check the direction of motors and change wiring if necessary.

• Check the components for defects, such as loosening or damage.

• Check the functions of safety devices.

!

copyrighted

document

- all

rights

reserved

by

FBC

«
...
45
46
47
48
49
...
»

Summary of Contents for 790031754































































Reviews:

No comments

Related manuals for 790031754

Brand: Yard force Pages: 150

Brand: Valex Pages: 20

Brand: Gartenteile Pages: 144

Brand: Femi Pages: 140

Brand: Feider Machines Pages: 15

Brand: Scheppach Pages: 88

Brand: Milwaukee Pages: 115

Brand: Campbell Hausfeld Pages: 48

Brand: Baileigh Industrial Pages: 48

Brand: tigair Pages: 7

Brand: XTline Pages: 30

DELTA S36-290 T2

Brand: ShopMaster Pages: 80

Brand: Holzstar Pages: 20

Brand: Holzstar Pages: 26

Brand: TACKLIFE Pages: 23

Brand: TACKLIFE Pages: 28

Brand: Workzone Pages: 34

Brand: Workzone Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands