50
EN
M1.1.TZHD30S-50S.NLFREN - 15032019
7. Operations
7.1 Electrical Operation
(
Fig.27
)
ON Button:
Starts the motor.
Hole for safety pin:
When installed pin, disables
the ON Button to prevent accidental startup.
STOP Button:
Turns machine.
Fig.27
7.2 Safety Precautions before Operations
The operation of power tools involves a certain
amount of hazard for the operator. Before
attempting regular work we recommend you get
the feel of operations using scrap lumber to check
settings. Read entire instructions before you start
to cut workpiece. Always pay attention to safety
precautions to avoid personal injury.
7.3 Operation
Plain sawing includes ripping and crosscutting,
plus a few other standard operations of a
fundamental nature. The following methods feature
safety. As with all power tools there is a certain
amount of hazard involved with the operation and
use of the tool. Using the tool with the respect and
caution demanded as far as safety precautions are
concerned will considerably lessen the possibility
of personal injury. However, if normal safety
precautions are overlooked or completely ignored,
personal injury to the operator can develop. It is
good practice to make trial cuts using scrap
material when setting up you saw for operation.
7.4 Crosscutting
Crosscutting requires the use of the miter gauge to
position and guide the work. Place the work
against the miter gauge and advance both the
miter gauge and work toward the saw blade.The
miter gauge may be used in either table slot,
however, most operators prefer the left groove for
average work. When bevel cutting (blade tilted),
use the table groove that does not cause
interference of your hand or miter gauge with the
saw blade guard.
Start the cut slowly and hold the work firmly against
the miter gauge and the table. One of the rules in
running a saw is that you never hang onto or touch
a free piece of work. Hold the supported piece, not
the free piece that is cut off. The feed in
crosscutting continues until the work is cut in two,
then the miter gauge and work are pulled back to
the starting point. Before pulling the work back it is
good practice to give the work a little sideways shift
to move the work slightly away from the saw blade.
Never pick up any short length of free work from
the table while the saw is running. A smart operator
never touches a cut-off piece unless it is at least a
foot long. Never use the fence as a cut-off gauge
when crosscutting. Never use the miter gauge in
combination with the rip fence.
7.5 Ripping
Ripping is the operation of making a lengthwise cut
through a board, and the rip fence is used to
position and guide the work. One edge of the work
rides against the rip fence while the flat side of the
board rest on the table. Since the work is pushed
along the fence, it must have a straight edge and
make solid contact with the table. The saw guard
must be used. The guard has anti-kickback fingers
and a splitter to prevent the saw kerf from closing.
Start the motor and advance the work holding it
down and against the fence. Never, stand in the
line of the saw cut when ripping. Hold the work with
both hands and push it along the fence and into the
saw blade as shown in Fig. The work can then be
fed through the saw blade with one or two hands.
When this is done the work will either stay on the
table, tilt up slightly and be caught by the rear end
of the guard or slide off the table to the floor.
Alternately, the feed can continue to the end of the
table, after which the work is lifted and brought
back along the outside edge of the fence. The
waste stock remains on the table and is not
touched with the hands until the saw is stopped
unless it is a large piece allowing safe removal.
ON
button
STOP
button
Hole for
safety pin
Figure 27
5 Operation
5�1 Electrical operation
See figure 27:
ON button:
Starts the motor
Hole for safety pin:
When installed pin, disables the ON button to
prevent accidental startup.
STOP button:
Turns machine off.
5�2 Safety precautions before operations
The operation of power tools involves a certain amount of hazard for the operator. Before attempting regular work we
recommend you get the feel of operations using scrap lumber to check settings. Read entire instructions before you start to cut
workpiece. Always pay attention to safety precautions to avoid personal injury.
5�3 Operation
Plain sawing includes ripping and crosscutting, plus a few other standard operations of a fundamental nature. The following
methods feature safety. As with all power tools there is a certain amount of hazard involved with the operation and use of the
tool. Using the tool with the respect and caution demanded as far as safety precautions are concerned will considerably lessen
the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to
the operator can develop. It is good practice to make trial cuts using scrap material when setting up you saw for operation.
5�4 Crosscutting
Crosscutting requires the use of the miter gauge to position and guide the work. Place the work against the miter gauge and
advance both the miter gauge and work toward the saw blade. The miter gauge may be used in either table slot, however,
most operators prefer the left groove for average work. When bevel cutting (blade tilted), use the table groove that does not
cause interference of your hand or miter gauge with the saw blade guard.
Start the cut slowly and hold the work firmly against the miter gauge and the table. One of the rules in running a saw is that
you never hang onto or touch a free piece of work. Hold the supported piece, not the free piece that is cut off. The feed in
crosscutting continues until the work is cut in two, then the miter gauge and work are pulled back to the starting point. Before
pulling the work back it is good practice to give the work a little sideways shift to move the work slightly away from the saw
blade.
Never pick up any short length of free work from the table while the saw is running. A smart operator never touches a cut-off
piece unless it is at least a foot long. Never use the fence as a cut-off gauge when crosscutting. Never use the miter gauge in
combination with the rip fence.
5�5 Ripping
Ripping is the operation of making a lengthwise cut through a board, and the rip fence is used to position and guide the work.
One edge of the work rides against the rip fence while the flat side of the board rest on the table. Since the work is pushed
along the fence, it must have a straight edge and make solid contact with the table. The saw guard must be used. The guard
has anti-kickback fingers and a splitter to prevent the saw kerf from closing.
Start the motor and advance the work holding it down and against the fence. Never, stand in the line of the saw cut when
ripping. Hold the work with both hands and push it along the fence and into the saw blade as shown in Fig. The work can then
be fed through the saw blade with one or two hands.
When this is done the work will either stay on the table, tilt up slightly and be caught by the rear end of the guard or slide off
the table to the floor. Alternately, the feed can continue to the end of the table, after which the work is lifted and brought back
along the outside edge of the fence. The waste stock remains on the table and is not touched with the hands until the saw is
stopped unless it is a large piece allowing safe removal.
copyrighted
document
- all
rights
reserved
by
FBC
