MW 790031754 Manual Download Page 24

Page: 24 / 62

M1.1.TZHD30S-50S.NLFREN - 15032019

2�4 Exigences en matière d’alimentation électrique

Liste des tensions les plus utilisées et précâblées :

Moteur

4 kW (5,5 HP)

Tension

380 V

Phases

3 Ph

Fréquence

50 Hz

Courant nominal

8,3 A

Précâblage

380 V / 3 Ph

Fils

L’alimentation en courant alternatif en régime permanent est de 0,9 ~ 1,1 fois la valeur nominale.

Fréquence

0,99 ~ 1,01 fois la fréquence nominale (50 Hz, fonctionnement continu)

0,98 ~ 1,02 fois la fréquence nominale (50 Hz, fonctionnement de courte durée)

Harmoniques

La somme des 2ème - 5ème harmoniques ne peut pas excéder 10 % de la valeur efficace de tension. Un supplément de 2 %

de la valeur efficace de la tension de ligne est autorisée pour la somme de la 6ème à la 30ème harmonique.

Tension asymétrique

Ni les composantes négatives ni les composantes à séquence nulle ne doivent dépasser 2 % de la composante à séquence

positive.

Protection électrique

L’utilisateur final doit prévoir un dispositif de protection contre les surtensions dues à la foudre et un dispositif de protection

contre les courts-circuits sur l’alimentation électrique.

Protection contre l’intrusion à l’entrée du câble d’alimentation entrant

La méthode d’entrée du câble d’entrée doit assurer un indice de protection IP54 lors de la finition de l’installation sur place.

2�5 Niveau sonore

Normes de référence

Les mesures des émissions sonores ont été effectuées conformément à la norme EN ISO 11202 pour la détermination du

niveau de pression acoustique aux postes de travail. Lorsque les niveaux de pression acoustique mesurés aux postes de travail

dépassent 85 dB(A), les mesures des niveaux de puissance acoustique ont été effectuées conformément à la norme EN ISO

3746.

Conditions de fonctionnement

Les conditions de fonctionnement pour la mesure du bruit sont conformes à l’annexe A de la norme ISO 7960:1995.

Résultats des tests

À VIDE

EN CHARGE

Lwa

101,3

104,1

Lpa

Position A

84,7

88,5

Position B

86,1

89,1

Position C

77,0

79,8

Incertitude associée

= 4 dB

Remarque : Le bruit de fond de l’entourage de la mesure est de 65,0 dB(A)�

copyrighted

document

- all

rights

reserved

FBC

Summary of Contents for 790031754































































Search results

Summary of Contents for 790031754

Reviews:

Related manuals for 790031754

Brands by name

Popular brands

MW 790031754, Manual

Search results

Summary of Contents for 790031754

Reviews:

Related manuals for 790031754

Brands by name

Popular brands