Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 5 | Manualshive

Page: 5 / 39

Munters WM54F Manual For Use And Maintenance Including Assembling Instructions Download Page 5

5

CE Declaration

Chapter

1

1

.

1

Disclaimer

Munters  reserves  the  right  to  make  alternations  to  specifications,  quantities,  dimensions  etc.  for  production  or
other  reasons,  subsequent  to  publication.  The  information  contained  herein  has  been  prepared  by  qualified
experts  within  Munters.  While  we  believe  the  information  is  accurate  and  complete,  we  make  no  warranty  or
representation  for  any  particular  purposes.  The  information  is  offered  in  good  faith  and  with  the  understanding
that  any  use  of  the  units  or  accessories  in  breach  of  the  directions  and  warnings  in  this  document  is  at  the  sole
discretion and risk of the user.

1

.

2

Introduction

In order to realize the full benefit from this product it is important that it is installed, commissioned and operated
correctly. Before installation or using the fan, this manual should be studied carefully. It is also recommended that it
is kept safely for future reference. The manual is intended as a reference for installation, commissioning and
day-to-day operation of the Munters fans.

1

.

3

Data for Fan Eco Design Directive

Fan description

(

*

)

Product information requirements

*

→

(according to ANNEX I -3.2 of regulation)

1

2

3

4

optional

6b

6c

7

8

Overall efficiency η%

Efficiency grade

Measurement

category

Efficiency

category

Target efficiency grade 2015

VSD must be installed with the fan

Motor power input at optimum energy efficiency [W]

Flow rate at optimum energy efficiency [m3/h]

Pressure at optimum energy efficiency [Pa]

RPM at optimum energy efficiency

Speific ratio

WM54F 1.5hp 3ph 50Hz OS

5

6

a

3

9,3

A

static 4

4,9

34,

4

no

1

310

3

0562

60,71

510

1

WM54F

2

hp 3ph 50Hz OS

3

9

,

8

A

static 4

4

,

4

3

5

,

4

no

1852

3

4755

76

,

35

5

66

1

* Fans tested are configured according to COMMISSION REGULATION (EU) No 327/2011 of 30th March 2011 - ANNEX II - 1.5. Efficiency values, according to

Commission Regulation (EU) 327/2011, refers to exhaust fans only.

«
...
3
4
5
6
7
...
»

Summary of Contents for WM54F








































Reviews:

No comments